Tablet Setup
IGNORE ALERT "The connected charger will take longer to charge. To charge faster, use the original charger and cable..."
- Power On Tablet (hold button on top left).
- Select the Gear icon at the top right of operating instructions screen (Password: 6456 - Submit).
- Select “Location Setup” from left column, and then type in the course name you want to find in the top search field. Watch out for extra spaces when typing the course name.
- If needed, verify the way your course is titled in the database by searching for the course at https://skydroid.net/courses.php. If the course is not in the database skip to the WiFi Download Method.
- If the course name starts like Country Club or Golf Club, search by the unique part of the course name instead.
- Be PATIENT it may take up to 2 minutes for the file to be located. Do not click on the screen repeatedly or too quickly. If you press on the screen too many times a pop up will display asking for a Kiosk password, which will cause you to have to restart this entire process.
- If there is a pop asking if you want to end the program or wait. Always select Wait.
- Select the desired course file that is displayed right below the course search field (Hit Save, then ok).
- Only tap the course file name once every 5 seconds to reduce the chances of the app crashing.
- Verify that this is done correctly
- Select “Exit” tab from the left column when finished.
- Press the “Start” button and hole selection to confirm tablet has been set up correctly.
Tablet Setup - WiFi Download Method
**If you cannot locate the course file at https://skydroid.net/courses.php reach out to your Club Car representative. Club Car will need to map the course, which may take a couple days. When this is finished follow the instructions on how to download a file.**
- Tap Screen Repeatedly (20x/second)
- Enter 1234 as PIN
- Setup WiFi connection
- Press Back Button
- Navigate to Gear Icon, then enter passcode 6456
- Select “Location Setup” tab on the left side.
- When the data fields load, scroll to bottom of screen
- Press the “Download A Course” button
- Navigate to the correct course
- Note: This course will need to be mapped first, so contact Club Car contact to make sure this is completed.
- Select “Save” button on top of screen
- Press OK to confirm
- Select “Exit” tab on the left side (you may need to scroll screen up to see this).
- Verify that course file loaded correctly
- Press Start button on Operating Instructions page
- Select 9/18 holes
- Verify course name is correct (top left)
Tablet in Safe Mode
- Hold Power Off and Volume Up buttons down (until after screen goes black and until words pop up)
- Using Volume UP/Down and Power buttons, restart tablet in Normal Mode.
- Make sure Fully Single starts and the TW App Load Correctly.
- If not, select the Fully Single Kiosk App
- Press the Start Kiosk Mode button
- Make sure slider is off and press the Yes button
- Select Fully Single App Kiosk and then Always
- Press Start on the TW app, select 9 or 18 holes, and then verify course name is correct (top left)
Tablet Screen Brightness
- Tap screen repeatedly (20x in a second)
- Type in password 3897
- Swipe from left edge of screen to the right
- Select Setting > Device Management > Screen Brightness
- Set the Screen Brightness to 250
- Reset Tablet
Sensor System Disabled
- The sensor disabled alert will be triggered at power up. If a single sensor trips 3 times in 30 mins or any combination of sensors trip 5 times in 30 minutes. (Note: This may also be caused by a towel or head cover hanging in front of the sensors or by inexperienced users repeatedly turning towards the unit while they are still connected to the Tempo Walk).
- Begin with a visual inspection of all 3 sensors on the front of the Tempo Walk. You should look for scratches and pressed in center sensors as a sign of damage. Sensors showing this damage should be replaced immediately. See the sensor replacement guide below for instructions on how to do this.
- Finally, after you complete the sensor replacement, power ON the Tempo Walk, wait 2 seconds after the audible alert finishes, and then press the neutral button 2 times to reset this alert. You will hear a beep to confirm the reset.
Tempo Walk Charging Steps
Status |
Situation |
Steps to Fix |
Tools Required |
Normal: Tempo Walk powers on, but won’t charge. |
Charger not plugged in right. |
Plug in normal charger (make sure to align tabs) and wait for progress % lights. If charger adapter is forced in the wrong way, the inline fuse can blow on the TW charger cable. Tilt the TW up and pull the fuse holder out to examine 10A fuse. This is located 12” from plug end, inside the TW frame area. |
None |
Stage 1: Battery % lights don’t work |
Battery went into protection mode. |
Press button to the open circuit breaker and then replug the normal charger and wait for progress % lights. Only close the circuit breaker arm after the TW is charging properly. |
None |
Stage 2: Battery % lights still don’t work |
Stage 1 charging doesn’t work. |
Leave circuit breaker open and charger plugged. Next, hold the mode button until 13.6V repair mode shows, they press it again until 12V repair is selected. Leave trickle charging overnight and try 24V normal mode after to see if it charges. |
None |
Stage 3: TW battery voltage below PCM threshold |
Stage 2 charging doesn’t work. |
Leave circuit breaker open and then plug in Hot Charger cable to trickle charge (5-48 hours). Then plug in the normal charger and wait for progress % lights. |
Hot Charger Cable |
Stage 4: TW battery voltage way below PCM threshold |
Stage 3 charging doesn’t work. |
Leave circuit breaker open, remove top plastic (careful with all wires). Next attach the Hot Charger cable with alligator clips to battery terminals. Finally, plug in the normal charger and wait for progress % lights. |
Hot Charger w/ alligator clips, and 7/16 hex nut with drill. |
Stage 5: TW battery is unresponsive |
Stage 4 charging doesn’t work. |
Watch training videos on how to replace the battery. |
7/16 hex nut with drill, and new battery |